VuQube V20 Operations Instructions Page 1

11200 Hampshire Avenue South, Bloomington, MN 55438-2453Phone: (800) 982-9920 Fax: (952) 922-8424www.kingcontrols.com20625 REV CSatellite Solu

This page intentionally left blank.Page 8

Page 9SECTION 3VUQUBE ANTENNA CONFIGURATIONThe VuQube Model V20 Automatic Satellite System is factory pre-set for DIRECTV standarddigital programming

Page 10DIRECTVSingle Satellite 101 Receive programming from the DIRECTV 101 satellite only.DIRECTV Plus: 101, 119Automatically switch between the 101

Page 11Note: This map is anapproximation only. Which trioworks best in a given locationmay differ from what is indicatedon the map.Dish HD & Dish

DIRECTV Plus (satellites 101, 119)1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then W

DISH 500 (satellites 110, 119)1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then WAIT

DISH HD Eastern Arc (satellites 62, 72, 77)1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, a

Page 15DISH HD Alternate (satellites 62, 110, 119)1. On the VuQube controller, press and release the ON button. Wait for the status light to flash or

HDTV (satellites 82, 91)1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then WAIT 4 MORE

This page intentionally left blank.Page 17

1. Turn on the TV and satellite receiver.2. On the VuQube controller, press and hold the ON button for 3 FULL SECONDS. The antenna will lock onto the

Page 197. When test is complete, a screen similar to one of the following should appear:(Screen graphics may vary.)If indicated results are not obtain

1. Turn on the TV and receiver. “Searching for Satellite” or similar will appear on TV screen.2. On VuQube controller, press and hold theON button fo

Page 21AUTOMATIC SATELLITE SWITCHING1. After you have properly configured the VuQube antenna for your satellite service, theVuQube will automatically

Page 22IMPORTANT! Perform this procedure only if you are unable to receive all of your HD programming in aparticular area of the country.You cannot c

Page 23IMPORTANT! YOU MUST RUN THE CHECK SWITCH AFTER SWITCHING TRIOS!IMPORTANT! YOU MUST RUN THE CHECK SWITCH AFTER SWITCHING TRIOS!DISH HD Eastern

Page 24If you have traveled a long distance since last performing a search, you can speed up acquisitiontime by setting the VuQube to start searching

Page 25CHANGE SEARCH ELEVATION TO 25°1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then

Page 26CHANGE SEARCH ELEVATION-ContinuedCHANGE SEARCH ELEVATION TO 48°1. On the VuQube controller, press and release the ON button. Wait for the statu

Page 27SECTION 5TROUBLESHOOTINGVuQube does not find satellite.(STATUS light flashes red or green.)STATUS light flashes orange. Before search: bad coax

Page 1DIRECTV®is a registered trademark of DIRECTV, Inc.Dish NetworkTMis an official trademark of Echostar Communications Corporation.Bell ExpressVu i

Page 28SECTION 6MAINTENANCEThe VuQube Satellite System has been designed to be maintenance and trouble free.For optimum signal strength, keep the encl

Page 29SECTION 7LIMITED WARRANTYEvery VuQube Satellite System is thoroughly inspected and tested before leaving the factory. It is covered by a one y

Page 30Notes:

Notes:Page 31

Page 32Notes:

11200 Hampshire Avenue South, Bloomington, MN 55438-2453Phone: (800) 982-9920 Fax: (952) 922-8424www.kingcontrols.com®

Page 2The VuQube V20 Automatic Satellite System provides simple, one-touch operation for easyaccess to all your favorite satellite TV channels. It is

Page 3KIT CONTENTS2. Unpack and identify all components (Fig. 2).SECTION 2INSTALLATIONFig. 2TOOLS AND MATERIALS REQUIRED1. Read thru the instructions

Page 4ANTENNA UNIT LOCATION AND INSTALLATION (FIG 3.)3. Determine the location of the antenna unit using the following criteria:a) The antenna unit is

Page 54. Mount the bracket to the cab (see bracket instructions-bracket sold separately). Removethe nuts from the threaded studs on the bottom of the

Page 67. Run wiring from the antenna unit to the location where it will be fed into the vehicle.Make sure external wiring is tied down securely (to a

Page 7INTERNAL WIRING9. Inside the vehicle, make the connections as shown in (Fig. 6), keeping in mind thefollowing important points:a) The connection